Irrigation and Sprinkler Leak Repair in Spring, Texas: leak detection specialist examining a wet patch of soil around a
We find the break, fix the line, and stop the water waste.

Irrigation and Sprinkler Leak Repair Spring TX

Irrigation and Sprinkler Leak Repair Spring TX starts with finding the exact break in your lawn line, not guessing. We handle sprinkler system leak repair Spring homeowners call about when a zone won't hold pressure, a head won't pop, or the water bill jumps. Licensed techs, same-day diagnosis, and a repair that holds through the next freeze.

Prepared local crewClear options firstFinal testing and walkthrough

Focused arrival windows

Useful updates and clear arrival timing.

Clear scope before work

Review the approach and price before deciding.

Prepared, clean crews

Equipped vehicles and respectful cleanup.

Local accountability

Neighbors serving neighbors with follow-through.

What is included

What Our Sprinkler Leak Repair Includes

Every irrigation and sprinkler leak repair call includes the diagnostic work needed to find the break and the repair needed to fix it. If the problem turns out to be a domestic line instead of the irrigation system, we tell you before any work starts and quote that repair separately.

01

Zone Pressure Testing

We run every zone at the controller and watch the meter to identify which lateral is losing water. This takes 20 to 30 minutes and prevents digging in the wrong place.

02

Electronic Leak Location

Acoustic leak detection equipment and a pipe locator trace the lateral and pinpoint the break. On poly and PEX tubing we can often hear the spray through the soil before we open a trench.

03

Pipe and Fitting Repair

We cut out the failed section and rebuild it with Schedule 40 PVC pipe, new pipe fittings, and solvent weld or solder. Repairs are pressure-tested before backfill.

04

Valve and Head Replacement

Stuck valves, cracked valve bodies, and broken heads get replaced with matching parts. We check the solenoid and wiring while the valve box is open.

05

Backflow Assembly Testing

We test the backflow assembly after any mainline repair and confirm it meets code. If it fails, we can replace it on the spot with a certified assembly.

06

Controller Reset and Walkthrough

We reset your run times and season adjust, then walk you through what failed, what we replaced, and how to drain the system before a freeze.

PLAN

Request a service estimate

Share what is happening and receive a clear next step from the local team.

Request estimate
Service overview

What Irrigation and Sprinkler Leak Repair Spring TX Involves

Irrigation and Sprinkler Leak Repair Spring TX is the process of locating a failed sprinkler line, valve, or head and restoring it so your zones pressurize and shut off correctly. We isolate each zone, pressure-test the lateral lines, and use acoustic leak detection equipment to hear water escaping underground. Most breaks sit at a fitting, a cracked PVC pipe, or a valve that never fully closes. We cut out the failed section, rebuild it with Schedule 40 PVC pipe and new pipe fittings, and test the zone before we backfill.

Spring sits on expansive clay soil that swells after heavy rain and shrinks hard in summer drought. That movement shears sprinkler laterals and cracks valve bodies. If your system is losing pressure or a zone stays wet, sprinkler leak detection Spring TX can save thousands of gallons a month. We also check the backflow assembly and controller wiring, because a stuck valve looks identical to a broken pipe until you test it.

  • Lower Water Bills — A single broken lateral can push a Spring water bill up $60 to $200 a month. We locate the break, repair it, and re-test the zone so you stop paying for water that never reaches your grass.
  • Protect Your Foundation — Water pooling next to the slab is a real problem on Spring's clay soil. Fixing an irrigation leak repair Spring, Texas homeowners put off for months keeps soil moisture even and reduces the risk of a slab leak or foundation crack.
  • Save the Landscaping — A dead zone kills St. Augustine fast in July. We restore pressure to the whole zone so every head pops and covers the way it did when the system was installed, without tearing up the entire yard.
  • Repair, Not Replace — Most systems do not need a full rebuild. We replace the failed section, valve, or head and leave the rest of the system alone, which keeps lawn sprinkler leak repair Spring costs in the hundreds instead of the thousands.
  • Same-Day Diagnosis — Call before 2 p.m. and we will usually have a tech at your Spring address the same afternoon. Emergency sprinkler leak repair Spring TX calls after a freeze or a mainline blowout get priority scheduling, including weekends.
  • Licensed and Insured — We are a state-licensed plumbing contractor, insured and bonded. Every repair is documented with what failed, what we replaced, and the parts used, so you have a record if you sell the house or file an insurance claim.
  • We Find It Before We Dig — Our sprinkler pipe leak repair Spring, Texas process starts with electronic leak detection system testing, not a shovel. That keeps the damage to your lawn small and keeps affordable irrigation leak repair Spring TX pricing realistic instead of paying for hours of exploratory digging.
  • Warrantied Repairs — Our pipe and fitting repairs carry a written warranty. If the same section fails again, we come back and make it right. We also leave you a zone map and controller settings so the next tech, or you, knows exactly what was done.
Irrigation and Sprinkler Leak Repair in Spring, Texas: leak detection specialist examining a wet patch of soil around a
A careful diagnosis makes every next step clearer.
The service timeline

How Our Sprinkler Leak Repair Process Works

01

Phone Intake

You tell us what the system is doing: a zone that won't shut off, a wet spot in the yard, or a water bill that jumped. We ask for your controller brand and zone count, then schedule a same-day or next-morning visit. Calls before 2 p.m. usually get a tech that afternoon.

02

Zone-by-Zone Testing

We run each zone at the controller and watch the meter. A zone that keeps spinning the meter after the cycle ends is the leaking one. This takes 20 to 30 minutes on a typical six-zone Spring system and narrows the search before we dig anything.

03

Locate the Break

We use acoustic leak detection equipment and a pipe locator to trace the lateral and pinpoint the break within a foot or two. On systems with poly or PEX tubing we can often hear the spray through the soil. No exploratory digging across the whole yard.

04

Repair and Rebuild

We cut out the failed pipe, fitting, or valve and rebuild it with Schedule 40 PVC pipe, new pipe fittings, and fresh solder or solvent weld. A typical lateral repair takes one to two hours. Mainline breaks and valve box rebuilds run longer.

05

Pressure Test and Backfill

Before we close the trench, we pressurize the zone and watch it hold for a full cycle. Then we backfill, tamp the soil, and reset the controller schedule. You get a walkthrough of what failed and what we replaced before we pull out of the driveway.

Irrigation and Sprinkler Leak Repair in Spring, Texas: leak detection specialist examining a wet patch of soil around a
Tools and methods

Tools and Methods We Use

01

Acoustic Leak Detection Equipment

Amplifies the sound of water escaping a pressurized line so we can pinpoint a buried lateral break within a foot or two before we dig.

02

Pipe Locator

Traces the path of irrigation laterals and the water service line so we know exactly where to trench and where the utility lines are.

03

Pressure Testing Kit

Isolates each zone and confirms whether the lateral holds pressure, which separates a pipe break from a stuck valve or wiring fault.

04

Thermal Imaging Camera

Reveals temperature differences from escaping water, useful on shallow lines and on backflow assemblies inside walls or mechanical rooms.

05

Video Pipe Inspection Camera

Lets us look inside a line after a repair or when we suspect root intrusion, collapsed pipe, or a break we cannot see from the surface.

06

Trenchless Repair Equipment

Repairs mainline breaks under driveways, sidewalks, and patios without tearing out the concrete, which keeps restoration costs down.

07

Moisture Meter

Confirms whether soil moisture near the foundation is coming from the irrigation system or from a slab or under-house leak.

08

Zone Isolation and Meter Testing

We run each zone at the controller and watch the meter with all other water off. A zone that keeps the meter moving after the cycle ends is the leaking one. This narrows the search to a single lateral in under 30 minutes.

09

Acoustic Pinpointing

Once the zone is isolated, we walk the lateral with acoustic equipment and listen for the spray. On PVC we usually get within a foot. On poly and PEX tubing the sound travels differently, so we confirm with a pipe locator before trenching.

10

Code-Correct Rebuild

We repair to International Plumbing Code and Uniform Plumbing Code standards, using Schedule 40 PVC pipe, proper pipe fittings, and solvent weld or solder rated for the line. Backflow assemblies are replaced with certified units and re-tested.

11

Pressure Test Before Backfill

Every repair is pressurized and run through a full cycle before we close the trench. If it does not hold, we keep working. You do not pay for a repair that fails the first time the controller runs.

Where this service helps

When to Call for Sprinkler Leak Repair

Irrigation and Sprinkler Leak Repair in Spring, Texas: leak detection specialist examining a wet patch of soil around a

Your water bill doubled after a dry summer month and the yard has a soft spot near a valve box.

We meter-test with every zone off, then pressure-test each lateral to isolate the leaking zone. Acoustic equipment pinpoints the break, and we rebuild the failed section with new PVC pipe and fittings. The zone holds pressure, the soft spot dries out, and your next bill drops back to normal usage.

A zone stopped working after the last freeze and the controller shows it running but nothing happens.

Freeze damage usually hits the valve, the backflow assembly, or a shallow lateral. We test the solenoid and wiring, check the assembly, and pressure-test the lateral to find the split pipe. The zone runs again, the assembly passes code, and we show you how to drain the system before the next freeze.

You are selling the house and the buyer's inspector flagged the irrigation system as leaking.

We run a full diagnostic, document every failed component with photos, and complete the repairs before closing. You get a written record of what was replaced and the warranty on the work. The system passes re-inspection, the closing stays on schedule, and the buyer has documentation for their file.

An HOA common area has a mainline break under a sidewalk and water is surfacing in the street.

We locate the break with acoustic and tracer equipment, then use trenchless repair equipment to fix the line without tearing out the concrete walkway. Water stops surfacing, the sidewalk stays intact, and the repair is documented for the HOA and its insurer.

Local execution

How Sprinkler Leak Repair Works in Spring

Spring's climate drives most of the sprinkler failures we see. Summer heat pushes systems to run daily, which stresses fittings and valves. Then the first freeze in December or January splits backflow assemblies and shallow laterals that were never drained. The soil here is expansive clay that swells after a storm and shrinks hard in drought, shifting several inches and shearing lateral lines at the fittings. Homes built in the 1980s and 1990s around Old Town Spring and Timberlane often have original poly laterals that are now brittle. Newer builds in Creekside Park and Auburn Lakes use PVC and PEX, which fail differently, usually at the valve box or a poorly seated fitting. If you need sprinkler system leak repair Spring TX 24/7 after a mainline blowout, we run emergency calls including weekends. Every repair follows International Plumbing Code and Uniform Plumbing Code standards, and we test the backflow assembly after any mainline work because it is a cross-connection device, not a sprinkler part.

01

Old Town Spring

Older homes with original poly laterals that become brittle and shear at the fittings after years of clay soil movement.

02

Gleannloch Farms

Larger lots with long lateral runs, so a single break can drop pressure across an entire zone and waste water fast.

03

Creekside Park

Newer PVC and PEX systems where failures usually show up at the valve box, the backflow assembly, or a poorly seated fitting.

04

Imperial Oaks

Heavy clay soil that swells after storms and shifts lateral lines, a common cause of cracked pipe at the zone tees.

05

Expansive clay soil that swells and shrinks with the seasons

The movement shears lateral lines and cracks pipe at the fittings. We expect to find at least one shifted or cracked fitting on most older Spring systems.

06

Hard freezes in December and January

Backflow assemblies and shallow laterals split when water freezes inside them. We see a spike in emergency calls the week after any hard freeze.

07

Summer heat that forces daily irrigation cycles

Constant pressurization wears valves and fittings faster, so leaks surface in August and September when the system is working hardest.

08

Mixed housing stock from the 1980s through new builds

Poly, PVC, and PEX all fail differently. We match the repair material to the existing line so the fix lasts.

Before and after

What a successful service visit changes.

Sheared Lateral in Gleannloch Farms

Before

A homeowner's zone three would not hold pressure and the water bill climbed $85 over two months. The yard had a soft spot near the valve box but no visible spray. We isolated the zone and located a sheared fitting about 14 inches from the box.

After

We rebuilt the section with Schedule 40 PVC pipe and new fittings, pressure-tested the zone through a full cycle, and backfilled. The zone now holds pressure and the next bill dropped back to normal usage.

Maintenance: Keep the controller on a seasonal schedule and walk the zones once a month. A soft spot after a storm is the earliest sign of a shifted lateral.

Frozen Backflow Assembly in Old Town Spring

Before

After a January freeze, the backflow assembly sprayed water against the house every time the system ran. The assembly had split at the bonnet and was failing its annual test. The homeowner had shut the system off entirely.

After

We replaced the assembly with a certified unit, re-tested it to code, and reset the controller. The system ran through all six zones the same afternoon with no spray and a passing backflow test.

Maintenance: Drain the backflow assembly and the shallow laterals before the first freeze each year. It takes ten minutes and prevents the most common winter repair we see.

Mainline Break Under a Driveway in The Woodlands

Before

Water was surfacing in the street from an HOA common area. The mainline ran under a concrete driveway, and the property manager expected a tear-out. We located the break with acoustic equipment and confirmed the line path with a pipe locator.

After

We used trenchless repair equipment to fix the mainline without removing the driveway. Water stopped surfacing, the concrete stayed intact, and the repair was documented for the HOA's insurance file.

Maintenance: Mark the mainline path on the HOA site plan and check the meter monthly with all zones off. Early detection keeps a mainline break from undermining pavement.

Problems we solve

Sprinkler Problems We Fix in Spring

Most sprinkler calls come down to four failures. We see them every week on Spring's clay soil, and each one has a different repair.

01

A zone that will not hold pressure

The zone runs but heads barely pop, so half the yard dries out while the meter keeps spinning and the water bill climbs. We isolate the zone, pressure-test the lateral, and locate the break with acoustic equipment. Most are sheared fittings or cracked PVC at a tee. We rebuild the section with Schedule 40 pipe and re-test the zone before backfill.

02

Water pooling in the yard between cycles

Constant wet soil on Spring's expansive clay softens the foundation bed and can migrate under the slab over time. A wet spot with the system off usually means a mainline break or a valve that never fully closes. We meter-test with all zones off, then locate and repair the mainline or rebuild the valve.

03

Water bill jumped with no visible leak

A buried lateral can leak for months without surfacing, wasting thousands of gallons and pushing the bill up $60 to $200 a month. We run a full system audit: meter test, zone-by-zone pressure check, and electronic leak detection on each lateral. If the loss is on the domestic service line instead, we diagnose that too.

04

Backflow assembly spraying or dripping

A failed assembly is a code violation and a cross-connection risk, and it can spray water against the house every cycle. We test the assembly, replace it if it fails, and re-certify it. Our techs hold Backflow Prevention Assembly Tester certification, so the repair meets code on the first visit.

Pricing and expectations

Sprinkler Leak Repair Pricing in Spring

$180 - $1,200 depending on scope

Typical 2026 pricing for irrigation and sprinkler leak repair in Spring runs $180 to $450 for a lateral line or valve repair, and $700 to $1,200 for a mainline break under concrete. The diagnostic is the same either way: we isolate the zone, locate the break, and quote the repair before we dig. If the problem turns out to be a domestic line instead of the irrigation system, we tell you and quote that separately. No surprise line items, no charge for the estimate.

A leaking zone can waste thousands of gallons a month and soften the soil around your foundation. Fixing the line costs a fraction of what foundation repair or a full system replacement runs, and our repairs carry a written warranty.

01

Depth of the line

Laterals buried 12 to 18 inches are quick to access. Lines under a driveway, patio, or sidewalk need trenchless equipment or concrete work, which raises the cost.

02

Pipe material

PVC repairs are straightforward. Poly and PEX need matching fittings and different techniques, and brittle older pipe may require a longer cut-out to reach sound material.

03

Lateral versus mainline

A single zone lateral repair is the most common and least expensive call. Mainline breaks affect the whole system and often sit under hardscape, which adds time and equipment.

04

Valve and backflow work

Replacing a valve or a certified backflow assembly adds parts and testing time. Backflow work includes re-certification, which is required by code after replacement.

05

Number of leaks

Clay soil movement often causes more than one break. We quote each additional repair at a reduced rate because the equipment and crew are already on site.

Proof behind the promise

Licensed, Insured, and Warrantied

Master Plumber LicenseTexas State Board of Plumbing Examiners (TSBPE)
Journeyman Plumber LicenseTexas State Board of Plumbing Examiners (TSBPE)
Backflow Prevention Assembly Tester CertificationTexas Commission on Environmental Quality approved program
OSHA Safety CertificationOccupational Safety and Health Administration
4.9/5Google — Found a sheared lateral in our Gleannloch Farms yard in about 20 minutes and had it repaired the same afternoon. Zone holds pressure, water bill is back to normal. Fair price and they cleaned up the trench.
4.8/5Yelp — Replaced our frozen backflow assembly after the January freeze and re-tested it on site. Explained how to drain it next winter. Professional, licensed, and no upsell on a full system replacement.
4.9/5BBB — Handled a mainline break under an HOA sidewalk in The Woodlands without tearing out the concrete. Documentation was thorough enough for our insurance claim. Would call them again.
Irrigation and Sprinkler Leak Repair in Spring, Texas: leak detection specialist examining a wet patch of soil around a
Technical expertise

Leak Detection Experience You Can Verify

Our technicians are state-licensed plumbing professionals who work irrigation and sprinkler lines every week in Harris County. We carry TSBPE licensing, and our field leads hold Master Plumber credentials with Backflow Prevention Assembly Tester certification. That matters because a sprinkler main ties into your domestic water service, and backflow protection is code, not optional. We work to International Plumbing Code and Uniform Plumbing Code standards on every tie-in and repair, and we use RIDGID and General Pipe Cleaners equipment for line inspection. When a sprinkler leak turns out to be a water service line problem, we can follow it without handing you off to another company.

  • State-licensed plumbing contractor under the Texas State Board of Plumbing Examiners
  • Backflow Prevention Assembly Tester certification for irrigation tie-in compliance
  • Acoustic leak detection equipment and thermal imaging camera on every diagnostic call
  • Trenchless repair equipment for mainline breaks under driveways and walkways
  • Code-correct repairs to International Plumbing Code and Uniform Plumbing Code standards
High Water Bill Investigation in Spring, Texas: leak detection specialist attaching a pressure gauge to an exterior hose bib
Customer stories

What Spring Customers Say

Marcus T.Homeowner, Gleannloch Farms

One zone stopped popping and the water bill went up almost $90. They pressure-tested each zone, found a sheared lateral about a foot from a valve box, and had it rebuilt in under two hours. The zone holds pressure now and the yard is dry. No digging up half the lawn.

Dana R.Homeowner, Old Town Spring

After the February freeze our backflow assembly was spraying every time the system ran. They replaced the assembly, re-tested it, and reset the controller schedule. Clean work, fair price, and they explained what froze and how to drain it next time.

Priya S.Property Manager, The Woodlands

We manage several properties and had a mainline break under a driveway. They located it with acoustic equipment, used trenchless repair equipment to avoid tearing out concrete, and had water back on the same day. Documentation was clean enough for our insurance file.

How much does sprinkler leak repair cost in Spring TX?

Most residential sprinkler leak repairs in Spring run $180 to $450 in 2026, depending on depth, pipe material, and whether the break is in a lateral line or the mainline. Valve replacements and backflow repairs sit at the higher end. Mainline breaks under concrete can reach $700 to $1,200 because of access and restoration. We quote the repair before we start digging.

Why is my sprinkler system leaking in Spring, Texas?

The three most common causes in Spring are clay soil movement shearing lateral lines, freeze damage to valves and backflow assemblies, and cracked PVC fittings at the zone tees. Expansive clay shifts several inches between wet and dry seasons, and that stress cracks pipe and pulls fittings apart. A pressure test tells us which one you have in under 30 minutes.

Can you repair irrigation leaks without replacing the whole system in Spring TX?

Yes. Most systems only need the failed section replaced. We cut out the broken pipe or valve, rebuild it with Schedule 40 PVC pipe and new fittings, and pressure-test the zone. Full replacement only makes sense when the pipe is brittle throughout or the system is undersized. We tell you honestly which one you are looking at.

Who repairs sprinkler leaks in Spring TX?

Spring Leak Detection repairs irrigation and sprinkler leaks across Spring and Harris County, including Old Town Spring, Gleannloch Farms, Champion Forest, and The Woodlands. We are a licensed plumbing contractor, so we can also handle the water service line tie-in and backflow testing that a lawn company cannot. Call (281) 248-8538 for same-day scheduling.

Frequently asked questions

Frequently Asked Questions

Not seeing your question? Our local team can help you understand urgency, scheduling and what to expect.

Ask the local team
High Water Bill Investigation in Spring, Texas: leak detection specialist attaching a pressure gauge to an exterior hose bib
Here when the problem will not wait

Schedule Irrigation and Sprinkler Leak Repair Spring TX Today

One leaking zone can waste hundreds of gallons a week and soften the soil around your foundation. We are licensed, insured, and we warranty our repairs. Call now and we will find the break, fix it, and test the line before we leave.

Contact the local team

Contact Spring Leak Detection

Call (281) 248-8538 and we will get a licensed tech scheduled, usually the same day. We answer the phone 24/7 for active leaks, and we cover Spring, Harris County, and the surrounding communities. Tell us what you are seeing and we will bring the right gear.

Request received. We will be in touch shortly.

Call now